Difference between revisions of "Makerbot Thing-O-Matic build notes"

From Collexion
Jump to: navigation, search
(Initial build session. All parts packages accounted for.)
Line 32: Line 32:
  
 
'''Accomplished:'''
 
'''Accomplished:'''
* Extruder assembly in progress
 
* Electronics mounting in progress
 
 
* FINISHED - X-stage (Automated Build Platform)
 
* FINISHED - X-stage (Automated Build Platform)
 
* FINISHED - Y-stage
 
* FINISHED - Y-stage
Line 39: Line 37:
 
* FINISHED - Motherboard firmware update
 
* FINISHED - Motherboard firmware update
 
* FINISHED - Extruder firmware update
 
* FINISHED - Extruder firmware update
 +
 +
'''In Progress:'''
 +
* Extruder assembly in progress (Next step: [http://wiki.makerbot.com/stepstruder-mk6-assembly-3mm#toc59 Superglue spacer feet to support].)
 +
* Electronics mounting in progress
  
 
'''For next time:'''
 
'''For next time:'''
 
* Check ABP belt's tooth count; it's really loose, and it may be the wrong one
 
* Check ABP belt's tooth count; it's really loose, and it may be the wrong one
 
* ''If a construction phase is incomplete, link to the instructions page and enter the title of the next step to be performed''
 
* ''If a construction phase is incomplete, link to the instructions page and enter the title of the next step to be performed''

Revision as of 10:54, 28 February 2011

This space is intended to document progress on our Makerbot build. It should contain any information that other builders or future users might need to know, as well as general build status.

GATHER TIMELAPSE FRAMES!! We'll put them together into a video at the end of the build.

  • while true; do sleep 10; wget http://172.30.1.253/jpg/image.jpg; mv image.jpg `date +%Y%m%d%H%M%S`_makerbot.jpg; done

or, remotely:

  • while true; do sleep 60; wget http://lamecam.com/collexion/cam0.jpg; mv cam0.jpg `date +%Y%m%d%H%M%S`_makerbot.jpg; done;

(as of Mon Feb 28 00:30 this is now happening server-side on lamecam. Bit late, I know, but...)


2/26/2011

Initial build session. All parts packages accounted for.

Tools to bring to the space for build sessions:

  • Utility knife and/or scissors
  • Needle-nose pliers


Broken rib, front
Broken rib, back

We broke one of the Automated Build Platform's wooden ribs (with bushings for the drive rods). Some of the corners are really delicate. We repaired it with epoxy inside, a dab of hot glue outside, and marked the joint with black arrows in case it causes problems down the road.


The ABP's conveyor belt was too wide, wider than it appears in photos of other people's platforms. We trimmed it down to about 0.5cm inside the foil heat spreader on either side.


The ABP's conveyor belt is also very tight. It's difficult to move by hand, and it's bowing the rollers on either end. The kit contains three loops of conveyor plastic and two strips of conveyor plastic that look like they're intended to be taped into loops. No explanation for the strips in the instructions, and no mention of roller tightness.


Accomplished:

  • FINISHED - X-stage (Automated Build Platform)
  • FINISHED - Y-stage
  • FINISHED - Z-stage
  • FINISHED - Motherboard firmware update
  • FINISHED - Extruder firmware update

In Progress:

For next time:

  • Check ABP belt's tooth count; it's really loose, and it may be the wrong one
  • If a construction phase is incomplete, link to the instructions page and enter the title of the next step to be performed